Shop headings: New Spares | Used Spares | Accessories | Brands
Long screw in polished alloy dipstick with O ring for models with a sump extension but without fairing lowers
This part is due back in stock soon, call 01484 841395 to reserve yours
28004950-z 28004950 GU28004950 28 00 49 50
2800 4950 2800.4950 28.00.49.50
£24.30
INC VAT
£20.25 EX VAT
Long screw in polished alloy dipstick with O ring for models with fairing lowers (dipstick protrudes through fairing to make oil level checking much simpler and more accurate)
Use this longer dipstick for models fitted with a sump extension, note that the dipstick extension is 80mm long which is shorter than the original part. Supplied with both O rings
This part is available by special order, request a quote
£59.50
INC VAT
£49.58 EX VAT
Polished aluminium instrument console kit for 80mm instruments (as used on Le Mans 1, 2, T3, V50 etc...). This high quality kit is specially made for Gutsibits and consists of the following parts:
Manufactured from 6mm aluminium, this this instrument binnacle will not fatigue with use and is an excellent way to present the standard 80mm Veglia instruments. Bolts to handlebar yoke clamps. NB instruments and ignition switch shown in photo for illustration purposes only.
This is a high quality UK manufactured part made exclusively for Gutsibits, do not confuse with lesser alternatives. These kits are often prepared to order so please allow for a couple of days delay before your order is sent.
NB This kit works with the ignition switch ELA17735, later type switches will not fit into the predrilled ignition switch hole. On models with cable operated remote odometer resets the reset knob will need to be relocated. Check the depth of your instruments before ordering, this kit is intended for 48mm deep instruments with 60mm stud centres
Instruments with 60 degree or similar angle drives to the rear will require you to enlarge cable cutouts in the plates that make up the rear of the kit
1 in stock
£205.00
INC VAT
£170.83 EX VAT
Dimensions:
6mm thick aluminium, 70mm centres on M8 mounting holes, for 48mm deep instruments with 60mm stud centres
Polished aluminium instrument console kit for 80mm instruments (as used on Le Mans 1, 2, T3 etc...). This high quality kit is specially made for Gutsibits and consists of the following parts:
Manufactured from 6mm aluminium, this instrument binnacle will not fatigue with use and is an excellent way to present the standard 80mm Veglia instruments. Bolts to handlebar yoke clamps. NB instruments and ignition switch shown in photo for illustration purposes only.
This is a high quality UK manufactured part made exclusively for Gutsibits, do not confuse with lesser alternatives.
NB This kit works with the ignition switch ELA17735, later type switches will not fit into the predrilled ignition switch hole. On models with cable operated remote odometer resets the reset knob will need to be relocated.
Note that on models with an electronic tacho (e.g. Cali 3) the stud hole spacing may be a few mm out and you will needto drill new stud holes in the rear of the surround. You may also need to very slightly enlarge the warning light holes
2 in stock
£205.00
INC VAT
£170.83 EX VAT
Dimensions:
For 35mm stanchions, 223mm usable handlebar, 75mm total height, 30mm tall stanchion clamp
Pair of adjustable Tommaselli clipons, quality aluminium castings and chrome plated tube
These clip ons pivot on the central bolt to adjust the handlebar angle, pull back angle is adjusted on the fork stanchion clamp. These clip ons are unsuitable for use with the PS12 handlebar master cylinder. Bar ends are held in by a rivet and some modification will be needed if you wish to fit bar end mirrors.
This part is available by special order, request a quote
£240.00
INC VAT
£200.00 EX VAT
£3.40
INC VAT
£2.83 EX VAT
Brembo PS 13 handlebar mounted clutch master cylinder, supplied complete with lever.
This part is available by special order, request a quote
£175.00
INC VAT
£145.83 EX VAT
Replacement blue LED in chrome bezel for Gutsibits clock surrounds ACA01001 and ACA01002
These 12v LEDs include a resistor, wires should be soldered to the mini spade connectors on the base of the LED
More than 5 in stock
£3.40
INC VAT
£2.83 EX VAT
Black and red 60mm round Moto Guzzi badge for Hepco and Becker panniers
Guzzi pannier badge.
More than 5 in stock
£13.86
INC VAT
£11.55 EX VAT
Complete 950cc piston and Nikasil coated barrel kit including gudgeon pin, piston rings and circlips. Piston is low compression. This is a 950cc upgrade for 850cc models
Components for one cylinder. The barrel is designed to fit the standard crankcase aperture on 850cc bikes so it is not necessary to modify the crankcase. For the 850 GT it may be necessary to enlarge the pushrod tunnel opening in the head gasket to suit the 850 GT valve gear placement
This part is available by special order, request a quote
18060102-z 18060102 GU18060102 18 06 01 02
1806 0102 1806.0102 18.06.01.02
£311.00
INC VAT
£259.17 EX VAT